ERFURT, MODEL PKZV III 500, CRANK PRESS
Crank press PKZV III 500
Model PKZV III 500
Main parameter 500t, table: 3150mm x 2100mm
Producer Erfurt
Technical specification:
-mechanical, single-acting, four-point press
Nominal force(kN)- 5000
Ram stroke(mm) - 500
Ram adjustment(mm) - 500
Shut height between table and ram(mm), max. - 1200
Number of ram strokes per min. - 20
Width between uprights(mm) - 3150
Ram area(mm) - 3150x2100
Table area(mm) - 3150x2100
Thickness of bolster plate(mm) - 225
Pressure of cushion(kN) - 1600
Max. motor input(kW) - 75
Dimension : LxWxH(mm) - 4700x4400x7500
Total weight of press(mm) - approx. 140 t
Ref. 812127
VORONEZ K2542 1600 TONS TRIMMING PRESS
Trimming press VORONEZ K2542 1600t
Year: 1976
Condition: full complete, partly dismantled
Bottom extractor is available
Tech data:
Maximum force ton-force 1600
Slider stroke length , mm 400
Number of courses rpm 10
The closed height mm 1120
Adjustment mm 220
Bed: mm
- from left to right 1800
- from front to rear 1800
Slider mm 1440 x 1500
Aperture in a bed mm 1250 x 1250
Windows in racks mm 1560 x 980
Weight of the machine kg 154 000
Press overall dimensions: mm 5050/4620/8720
Ref. 812128
HBE 80 TONS MANIPULATOR
Specifications:
Carry Capacity, Nominal – 800, KN
Tongs Clamping moment – 1,600, kNm
Tongs openings, without inserts, round – 800/2,000, mm round
With inserts – 200-80, mm round
With extension arms – 100, 2,800, mm round & square
Max. turning diameter with extension aims – 3900, mm
Min. tongs cestre height above rails – 1700, mm
Vertical stroke of tongs parallel to floor – 2,800, mm
Vertical titling angle of tongs up150, down to foor
Horizontal side shift of tongs + 300, mm
Horizontal slew angle of tong + 150, mm
Horizontal movements of tongs in forging directing, relative to carriage +400, mm
Centre rail distance 5,000, mm
Overall dimensions :
Width, approx. 6,800, mm
Height, approx. 5,400, mm
Length, approx. 15,510, mm
Speed times;
Forging 0-30, m/min
Traveling 0-50, m/min
Turning of tongs 0-8, RPM
Lifting and lowering of tongs, compl, stroke 90, mm/sec
Tilting of tongs, compl. Stroke 90, mm/sec.
Side shifting of tong, compl.stroke 80, mm/sec
Clamping of tongs, compl. Stroke 70, mm / sec
Accuracy:
Traveling + 3 mm
Turning + 10
Total electrical capacity installed, approx. 495, Kw
Total delivery of the main pumps - unfixed – 1/min
Total capacity of accumulator - unfixed – 1/min
Usable capacity of accumulator – unfixed – 1/min
Cooling capacity, with max. water inlet tem. 360C, min – unfixed – Kw
Travel distance – 30, m
Weight on rails approx., Mechanical + Hydraulic – 350,t
Ref. 9124
DANGO 30 TONS MANIPULATOR
Specification
Length 10397, mm
Height, min./max. 5109, mm
Width 4400, mm
Rail Gauge 3500, mm
Rail top sidth, minimum required 120, mm
Travel distande 15, m
Machine weighr, approx. 125000 kg
Carrying – capacity, max. 400, Kn
Moment tong, max. 800, kNm
Moment max, front weels 1720, kNm
Stability factor 2.1
Tongs (two sets are provided)
Set1 opening ranges
-Max Round 1600, mm
-Max. Squre 1347, mm
-Max. Round and Spuare 310, mm
Set2 opening ranges
-Max. Round 1512,mm
-Max.Squre 1237, mm
-Max. Round and spuare 200,mm
-Tongs turning circle 2425,mm
-Tongs open/close 7/10, sec.
Tongs (peel) parallel vertical lift
-Peel C/L lowest position to floor 900, mm
-Peel C/L highest position to floor 2700,mm
-Peel parallel lift 1800,mm
-Peel lift / lower speed – Zero 1 to 150 / 150 mm/sec
Tongs (peel) tilt
-Peel tilt upward, out of horizontal position 8, degrees
-Peel tilt downward, out of horizontal position 10, degrees
-Tilting speed – Zero to 2.50 deg/sec.
Tongs (peel), Lateral shift
-Lateral shift stroke + 210, mm
-Shifting speed – zero to 100 mm/sec.
Tongs (peel) Rotate Drive
-Torque of peel rotate drive 90 / kNm
-Speed of peel rotate drive, max 18, rpm
-Accuracy + 0.250 degrees
Traverse Drive, Backlash – Free Drive
-Travel speed – Zero to 1000 mm/sec.
-Acceleration with load (300 Kn) - 3 m/SEC^2
-Accuracy + 2 mm
Ref. 9125
