TS PLZEN 8000 TON OPEN DIE FORGING PRESS Year: 2011
8000 TON OPEN DIE FORGING PRESS
Make: TS PLZEN(CZECH)
Type: Full Down 2 Column Press
Year: 2011
Nominal dorging,cogging force:6000ton
Upsetting force:8000ton
Maxium press stroke:2500mm
Press daylight:6100mm
Press force: (one-central cylinder:2000ton, two side cylinders:4000ton,3 cylinders:6000ton)
Distance between columns inside:2000mm x4200mm
Number of pull back cylinders:4
Forging tolerance meadured on hot workpiece:plus minus 1mm
Tanle size:3150mmW x8400mmL x4000mmLEFTx4000mmRIGHT
Die magazine:3
Tolerance of lower dies to be shifted die:plus minus 2mm
(Press speed)
-Forging speed at 6000ton:Max.63mm/sec
-Upsetting speed at 8000ton:Max 48mm/sec
-Advanced speed:250mm/sec
-Return speed:250mm/sec
-Die table slide forward:300mm/sec
(Press force)
-Forging at 320bar:6000ton
-Upsetting at 420bar:8000ton
-Return at 300bar:1130ton
-Table shift at 300bar:200ton
-Die shift at 300bar:100ton
-Die magizine at 300bar:200ton
(SPM)
Press stroke/ Penetration /Return stroke /SPM
3 cylinders 80mm 160mm 20
3 cylinders 40mm 90mm 30
1 cylinder 5mm 20mm 80
Main motors:400KW x 9sets, 3300V,1800rpm
Hydraulic pumps: 9sets,Oilgear type
(Total power supply)
9sets x main motor: :400KW 3300V,1800rpm
3 sets x booster motor:160KW, 440V,1800rpm
1set x piliot pump:75KW 440V,1800rpm
1set x cooling and filitering motor:55KW 440V,3600rpm
1set x Lubrication:2.2KW 440V
4sets x oil heater:20KW,445V
(Dimension of press)
Above floor:10370mm
Depth:14200mm
(Work Capacity)
Max. Diameter:9000 mm
Max.Length:20000 mm
Max.Weight:150 ton
High speed(Super alloy,Stainless steel, Carbon steel Low alloy forging)
(200MT MANIPULATOR)
Make: GLAMA(Germany)
80ton
Year: 2011
Mitsubishi 20tons Cross Forging Roll Line
Cross Forging Roll Line
Make: Mitsubishi(Japan)
Year:2000
Roll dice diameter: 1000mm
Roll diameter:9 20mm
Roll width: 700mm
Roll rpm: 10
Roll power: 20ton
Roll rotation torc: 14ton-m
Material diameter: 50-100mm
Worpiece length: Max 500mm
Main Motor: 150kw x 8p
Weight: 37ton
Including frequency heater(1000KW),
Mold 7 Units are included
Ref. No. CGS61716
NIKO 4000tons Friction Screw Press Year;1990
4000ton Friction Screw Press
Make:NIKO(JAPAN)
Year;1990
Usages:Forgings for the automotive industry and commercial
vehicles such as crankshafts, axles, connecting rods or
transverse links
Bolster area: 2350mm(R-L) x2100mm(F-B)
Stroke:600mm
Dieheight:1390mm
Lowering speed:700mm/sec
Inertia energy: kg-m:40,000
Cycle time: 150seconds
(Pressure block down device)
-Stroke:600mm
-Rising speed:250mm/sec
-Lowering speed;60mm/sec
(Rod float device)
- stroke;40mm
(Rod shift device)
-Stroke:2500mm
-Forwarding speed;250mm
-Back speed: 250mm/sec
(Rod down device)
-Stroke:100mm
-Rising speed:100mm/sec
-Lowering speed:100mm/sec
(Up pascal clamp)
-Max.1635mm
-Min. 1553mm
-Stroke:35mm
-Forwarding speed:50mm/sec
-Back speed:50mm/sec
(Safe block device)
-Stroke:65mm
-Rock speed:50mm/sec
-Un-rock speed:50mm/sec
(Strip pin device)
-Stroke:200mm
-Rising speed:50mm/sec
-Lowering speed:50mm/sec
(Massage roller)
-Stroke:200mm
-Pressing speed:50mm/sec
-Drawing speed:50mm/sec
(Die lift device)
-Stroke:3mm
-Rising speed:50mm/sec
-Lowering speed:50mm/sec
(Product extracting device)
-Stroke:820mm
-Rising speed:250mm
-Lowering speed:250mm/sec
(Press dimension)
7510mm(R-L) x 8860mm(F-B) x9680mm(H)
Ref. CGS61717
Seohoon 1500tons Open Die Forging Press Year: 2011
1500ton Open Die Forging Press
Straight side frame type
Make: Seohoon(Korea)
Year: 2011
Stroke:1500mm
Table: 2000x4500mm
Cylinder ram diameter: 800mm
Top shifting device
Top die clamping device
Hydraulic pump:3units
(Motor)
Quantity:3units
Make:Hyundai(Korea)
Year:2011
160KW x 3 units
440V, 6P
Weight:Approximately 200ton
