NKMZ, KRAMATORSK, MODEL PKKSH4000, 4000 TONS HOT FORGING PRESS
Hot-forging press, model PKKSH4000, 4000t, (NKMZ, Kramatorsk), good working condition.
Year - 1967.
Force, t..............................4000
Slide stroke, mm................400
Table size, mm..................1620x1570
Main motor, Kw.................185
Height of the press, mm....8680
Height ver floo, mm...........6820
Press weight, t..................375,75
Ref. 812111
SMERAL, LZK4000, 4000 TONS HOT FORGING PRESS
Hot-forging press LZK4000, 4000t, (SMERAL), working, complete.
Year - 1977.
Specs:
Force, t : 4000
Distance clear between uprights, mm : 1580
Slide stroke, mm 380
Number of slide continuous strokes per minute : 60
Distance between bed and slide when in down position and adjustment up, mm1000
Adjustment stroke, mm : 10
Bed dimensions, mm:
left-to-right 1520
front-to-back 1600
Upper knockout stroke, max, mm 50
Lower knockout stroke, max, mm 80
Drive motor power, kW 200
Press overall dimensions, mm:
left-to-right 4700
front-to-back 4820
height 7670
Height above floor level, mm 8690
Total weight of the press, kg 250 000
Ref. 812112
NKMZ, KRAMATORSK, K8548, 6300 TONS , HOT FORGING PRESS
Hot-forging press K8548, 6300t, (NKMZ, Kramatorsk), dismantled condition.
Year - 1967.
Needs to repair:
- bronze friction bearing;
- some teeth of the clutch are broken.
Specs:
1. Force, t 6300
2. Slide stroke, mm 460
3. Strokes number of the slider per min.40
4. Distance between table and slide, mm 1150
5. Adjustment distance, mm 15
6. Press ram dimensions, mm:
Left-right 1680
Front-back 1680
7. Table dimension, mm:
Left-right 1920
Front-back 1950
8. Upper ejector: numbers of pin 1
Max. stroke, mm 100
Travel adjustment (staged), mm 0-25-50-75-100
Force, t*force 30
9. Lower ejector: number of pins 3
Distance between pins, mm 450
Max. stroke, mm 300
Travel adjustment (continuous), mm 15-300
Force, t*force 65
10. Dimensions of the lateral windows, mm:
Width 1100
Height 1280
11. Electric motor: type
Voltage, V AK313-52-10
Power, KW 6000
RPM 400
590
12. Press dimension in plan, mm 6300х9200
13. Height of the press, mm 11725
14. Height above floor of the press, mm 9150
15. Press weight (without electric equipment), t 613
16. Electric equipment weight, t 9,9
17. Air working pressure, kg/sm2:
Clutch 5,0-5,5
Counterbalancing device 5,5-6
18. Total power of the electric equipment, Kw 430
Ref. 812113
WILLIAMS & WHITE 4 POST DOWNACTING HYDRAULIC PRESS
A)
3 X 7860 Ton Siempelkamp Downacting Hydraulic Presses New: 2000
Serial Numbers: 171.1 / 171.2 / 171.3
Press Force: 7,860 US Ton (70,000 kN)
Stroke: 39.37" (1000 mm)
Daylight Opening: 78.74" (2000 mm)
Overall Length of Bed: 216" (5.486 meters)
Overall Length of Ram: 141" (3.581 meters)
Pressing Area: 137.9"LR x 78.74" (3500 mm x 2000 mm)
Tool Weight: Upper - 3235 Ton (30,000 kg)
Tool Weight: Lower - 6470 Ton (60,000 kg)
Pressing Speeds: Approach: 840 IPM (350 mm/s)
Working Speed Maximum: 96 IPM (40 mm/s)
Return Speed: 400 IPM (164 mm/s)
Window Opening: 139.76" (3500 mm) LR x 80.70" (2050 mm) FB
Equipped With:
Rolling Bolster Plates Through Windows
Hydraulic Units - Rexroth Top Mounted (4) Main 200 HP Motors - 4700 Gallon Cap.
Electrical Power - 460V/60Hz
Material Tooling Transfer System
Overall Height Above Floor: 283.5" (7200 mm)
Approximate Weight: 520 Ton
Note: Hydroforming Intensifier and Pumps Available at additional cost !!!!
PHOTOS WERE WHEN PRESSES WERE LAST IN SERVICE !!!!!
Condition: Very Good - Reported to have only 500 hours use.
Currently dismantled and ready to load !!!!!
B)
5000 Ton Williams & White 4 Post Downacting Hydraulic Press
New: 1997
Serial Number: C-4745
Capacity: 5000 Ton Pressing @ 4097 PSI
400 Ton (Stripping)
30 Ton Net Lift @ Fast Open
Stroke: 72"
Daylight: 112" (over Bolster)
Shut Height: 40"
Bed Area: 200" LR x 96" FB
Slide Area: 200"LR x 96"FB
Distance Between Columns: 202"
Distance Floor - Top of Bolster: 20"
Speeds: 800 IPM Advance
25 - 275 IPM Intermediate Pressing (to 1000 Ton)
6 - 60 IPM Pressing
30 - 200 Stripping
800 IPM Rapid Return
Equipped With:
Hydraulics:
Top Mounted
(2) 35" Diameter Main Cylinders / Single Acting
(2) 18-1/8" x 15" Diameter Kicker Cylinders / Double Acting
Floor Level Fill / Drain / Oil Level Sight Temp Gauges
(4) Oil Gear Axial Piston #PVV540 Primary Pumps
Denison Vane Auxilary Pumps
Intensifier for Hydroforming
Electrics:
Allen-Bradley PLC-5/40 Series Processor w/ Allen-Bradley Panelview Color Touch
Screen for Operator Interface w/ Minimum of 25% Spare I/O Capacity
Memory for Part Storage / Fault Monitoring / Temposonics
250 HP Main Motor / 1200 RPM
Trabon Automatic Lubrication System
Approx. Overall Dims.: 250" L-R x 156" F-B at floor / 250" L-R x 278" F-B at crown
Approximate Height Above Floor: 408" / Approx. Depth Below Floor: 90"
Estimated Total Weight: 838,000 Lbs.
PHOTOS WERE WHEN PRESS WAS LAST IN SERVICE !!!!!
We purchased this press from General Motors, Pontiac, Michigan Plant. They were using it for Hydroforming. We have moved it into our Ferndale, Michigan storage warehouse. It is offer loaded on buyers carriers, for immediate delivery.
All specifications are subject to verification by buyer.
C)
3500 Ton Williams & White 4 Post Downacting Hydraulic Press
New: 1998
serial# C-4755
Bed Size: 177" x 120"
Daylight: 86"
Shut Height: 34"
Stroke: 52"
D)
3000 Ton Williams & White 4 Post Downacting Hydraulic Press
New: 1998
serial# C-4801
Bed Size: 180" x 120"
Daylight: 99"
Shut Height: 45"
Stroke: 54"
E)
2000 Ton Williams & White 4 Post Downacting Hydraulic Press
New: 1998
serial# C-4780
Bed Size: 150" x 90"
Daylight: 91.75"
Shut Height: 49.75"
Stroke: 42"
Ref. 812102
