KURIMOTO F-2500 Hot Forging Press (Mass, 300 TN)
Hot Forging Press KURIMOTO F-2500
YOM: 1977
Condition: good working
Technical specification:
Rated force 2500 TN
Slide stroke, 320 mm
Frequency of the slide strokes per min 55
Distance between table and punch plate
of slider in case of upper table location, 890 mm
Adjustment, 16 mm
Bed dimensions, 1250x1400 mm
Slider dimensions, 1100x1150 mm
Air pressure consumption, 5 kgs/cm2
Drive power 110 kW
Stroke of bottom extractor 60 mm
Stroke of upper extractor, 50 mm
Mass, 300 TN
Ref. CGS11423
ITALPRESSE M 1100 Diecasting
ITALPRESSE Diecasting
Mod: M 1100
Closing force: t. 1100
Injection force: t. 950/840
Ejection force: t. 480
Distance between tie bars: mm. 945x945
Ø of entry of the cylinder: mm. 185
Ø of the pipe that enters in the mould: mm. 94
Tie bar diameter: mm. 195
Platen dimensions (WxH): mm. 1500x1520
Tie bar height (min-max): mm. 425-1040
Moving platen stroke: mm. 950
Max. shot weight: kg. 23
Machine weight (approx.): t. 55
Size (LxWxH): m. 10.2 x 3 x 3.15
Ref. CGS81434
Open Die Forge Rail Mounted Ingot Manipulator 35t Nominal
Open Die Forge Rail Mounted Ingot Manipulator 35t Nominal -
57t Maximum Lifiting Capacity, Mfg. By Sms Sutton
Year Of Manufacture: 1992
Model Number: S80.1svz
Capacity (Tons): 35/57 Tons
Material Previously Handled:
Material: Hot Ingot Steel
Car Design:
Type Of Car: Floor Type
Lift Operation: Hydraulic
Max Jaw Opening: 42 Inches
Manipulator Rapid Traverse: 33 In./Sec.
Rotation Speed: 2-24 Rpm
Close Speed: 4 Ips
LOAD MOMENT: 290 Ft. Ton
WHEEL GAUGE (INCHES): 130 Inches (3,302.000 mm)
COMMENTS:
Travel Distance 40', Tong rotation Torque 75,000 ft. lbs.,
braking torque 100,000 ft. lbs.,
tong gripping range 10" - 42" without tong change,
load moment ctr. of jaws 290 ft. Ton, when measured from front
axle 560 Ft. Tons, short time overload capabilities 650 Ft. Tons.
lowest peel center above rails - 41.5 In.,
Highest Peel Ctr. above Rails - 77.2 In.,
Tilt down Angle - 12 deg., Tilting Up Angle 6.5 deg.,
Traveling Speed Forging 0-16.5 In./sec.,
Peel lifting and lowering 4.7 In./Sec.
Ref. CGS81435
Morgan Manipulator 15 Ton Capacity
1 Morgan Manipulator 15 Ton Capacity
•, Built 1981, Model No. 15, 7 Motion Track Type Forging Manipulator
• Operation - Rails And Gear Rack
• Drawings And Manual Available
• Spare Parts
• Specification Sheet And Drawing Attached,
• Decommissioned In December 2010,
• Spares Including Full Hydraulics, Etc. A “Rough” List Of Items Available Upon
Material Previously Handled:
Approximate Weight (Lbs.): 30,000 Pounds
Max Jaw Opening: 43.5 Inches
Jaw Outside Diameter: Open 82.5 Inches
Manipulator Rapid Traverse: 242.4 Fpm
Forging Transverse: 121.200 Fpm (36.942 Mpm)
Forge Stroke: +/- 6 Inches
Rotation Speed: 16 Rpm
Lift - Low/High: 36 Inches (914.400 Mm)
High Parallel: +5 Deg.
Low Parallel: -10 Deg.
High Parallel Above Rail: 36.500 Inches (927.100 Mm)
Low Parallel Above Rail: 72.500 Inches (1,841.500 Mm)
Equipment Specifications
Side Shift: +/- 12 Inches
Slew: +/- 8" Inches
Tong Clamp Moment: 169 Tons (153.314 Mt)
Close Speed: 2.34 Inch/Sec
Load Moment: Front Wheels
Peel Driving Torque: 15,356 Ft./Lbs.
Wheel Diameter (Inches): 24 Inches (609.600 Mm)
Rail Size: 175 Lbs./Yrd
Wheel Gauge (Inches): 126 Inches (3,200.400 Mm)
Wheel Base (Inches): 199 Inches (5,054.600 Mm)
Hydraulic Oil Capacity: 400 Gallons (1,514.164 Ltr)
Pressure: 2200 Psi
Tong Pressure: 2600 Psi
Heater: Yes
Heat Exchanger: Water
Ref. CGS81436
