PAPER MACHINE 3100 MM DECKLE
PAPER MACHINE 3100 MM DECKLE
Paper machine: fourdrinier with long wire section for making tissue and towel papers.
Grammage 15 to 45 gsm. Production 35,000 t/year. Production in various colours. Furnish is 100% mixed waste paper. In recent years production has been 18 to 20 gsm dry crepe and 38 to 54 gsm wet crepe papers. Can produce up to 100gsm wet Crepe papers. Operating speed 700 m/min. 80 t/ day at 38gsm/ speed 580 m/min.
Machine efficiency on 50 gsm wet crepe is 85%.
The machine sectional drive is on the left from the flowbox. Year of build is 1989 by Over Mechanica with various rebuilds over the years.
All well maintained and in good condition.
The mill is self-contained with package boiler, spares and final effluent treatment.
The plant is well supported with documentation drawings etc.
This is a versatile machine with a foudrinier wire, yankee and eight after dryers.
The plant has had investments of five million pounds in recent years.
Consumption data:
Power approximately 0.73 MWh/t
Fresh water approximately 30 m³/t
Steam approximately 1500 kg/t
Stock preparation
Two De Zurich and three Metso Consistency transmitters.
All water and stock/pulp pipes are stainless.
All stock chests are concrete with side entry agitators.
Lamort 18 m³ stainless steel pulper fed from OK conveyor with side entry. Conveyor on load cells feeding into a Lamort batch operated HC pulper with a helical rotor. Batch operation and consistency 12%. The mill has a spare rotor for this pulper. Also a spare base section.
Lamort dumping Poire size two in stainless with Lohse pneumatic valves. Rejects dumped onto a flat belt conveyor and then into an external skip.
Sicma wire baler for wires removed from waste paper bales.
After pulper dump chest. Cleaning is by two Lamort HD cleaners with auto pneumatic dump valves. Next stage is a Lamort CH horizontal screen in stainless: model CH5 with 2.2 mm holes. Rejects are treated with an Esher Wyess reject sorter, model one.
Next stage is a Lamort CH 7 horizontal stainless steel screen currently not used due to cleanliness of the pulp.
Back water fibre thickening is by an Andritz screw press model SCP7541M/16178 installed in 2005. The scew press also washes out fillers from the pulp.
Broke pulper
Lamort stainless batch pulper with an OK conveyor. Batch operation, consistency approximately 8%, with a perforated screen plate below the rotor to catch any large contaminates. In line is a Lamort HD cleaner with pneumatic auto slide valves. This is not used as the quality of broke was clear of HD particles.
All water, stock pumps are Scann manufacture and this includes the pumps on the final water floatation clarifier.
Refiner
Esher Wyess DSR 20” refiner with auto load control motor. 250 kw and 985 rpm.
Five stage Celleco LD cleaner system: Cleanpac models.
Machine pressure screen: Lamort SP 800 in stainless steel.
Flowbox / Wet End
Overmechanica flowbox hydraulic operation, stainless steel, manual profile adjustment, slice width 3200mm. Stainless clad cantilevered wire section, vacuum assisted foils, polyethylene tops/foils, plain breast roll, guiding system, auto wire tension, HP and LP showers.
Press sections
Most of press section box frames replaced with stainless build, rubber covered felt rolls, auto felt guide, auto felt stretcher. Uhle boxes and seamed felts are used.
First press: Overmechanica 880mm diameter, suction press roll with a bronze shell. Polyurethane cover and cast iron box.
Second press: Overmechanica 620mm diameter plain roll with a polyurethane cover.
Tail feed by Fibron air transfer.
Yankee Dryer
Dryer cast iron on A/F bearings, working pressure 8.8 bar pressure, diameter 3048mm, face 3442mm, bearing centres 4102mm, width over bolts 3647mm, paper width 3276mm, shell thickness 38.16mm. Metal sprayed by Voith in 2012. Design speed is 720 m/min, suction press roll loading 470 pli, plain press roll 450pli, auto oil lubrication, Kadant steam joints, Kadant Confromatic creping and cleaning doctors. Press loadings on yankee: first nip 82.31 KN/m and second nip 78.81 KN/m.
Drive is sectional electric via a Santasalo Hollow gear unit with an independent lub system.
Brunnschweiler dryer hood
Spare Yankee
The mill is including a spare Beloit Yankee dryer, year 1968, of similar dimensions and pressures. The dryer is currently on site, protected and stored on a purpose designed cradle.
After dryers
Eight after dryers on A/F bearings with auto lub system, guides and tensioners, The dryers are 1500mm diameter, bolted ends, sheathen rope feed. Operating pressure 7.93 bar, open gear drive from sectional independent drive motor. Kadant steam rotary joints the dryers have own hood with front opening door.
Voith/Fibron tail transfer system via Lippke cross machine measuring O frame.
In line slitting section manual set maker Mario with twelve slitters.
Slit edges are transferred via a trim fan to a continuous hydraulic baler with hopper and air separator. Auto wire feed for bales.
Reel up
Conventional horizontal reel up Overmaechanica manufacture with electrically operated primary arms, hydraulic operated secondary arms. Roll diameter 2000 mm, expanding core shaft centres for 202mm diameter cores.
Adjustable core shaft removing system located at the dry end of the machine.
Vacuum pumps
Two vacuum pumps in the machine rear and upstairs: Nash CL 1002. Fans for vacu foil units on the wire section.
Drive
The drive is sectional electric and ABB manufacture. Some drive parts with upgrades.
The machine house has a machine crane traversing the total length of the machine house and upper stock preparation area. Rated at 8.5 ton. The dry end has purpose made lifting beams with hooks for expanding reel bars and complete paper rolls. Within the stock preparation areas there are lifting points and fixed beams to enable maintenance.
Heat recovery systems
Metso external recovery system in stainless steel.
Water treatment
Metso Optidaf: year 2006 in stainless steel with level control, inspection window with sludge density control meter. Overhead camera to keep watch from control room.
Boiler
Robey boiler: duel fuel oil or gas. Saakke burner. Mill uses gas. Package design, maximum capacity 37,000 lbs/hr, at 15 bar pressure, working at 14 bar pressure. Year 1986.
DCS/QCS
Honeywell TDC 3000 for the analogue control with GEC Gem 80 system. QCS uses Lippke scanner controlling profile, gsm and moisture.
Power
Input power to the mill is 11,000 volts. Then down to 3300 volts. Power use in mill: 415v and 230 v AC. Transformers, HT and LT panels, starters’ switchgear and cables are included.
Air
Atlas Copco screw compressor operating at 6.7 bar pressure, 900 ft³/min. Air dryer and air reservoir.
NB. The machine is well supported with spare gearboxes, motors, valves, gear wheels and many small spares.
The building is also available under separate negotiation.
Ref. 51351
USED PAPER MILL
Paper Mill can be seen in operation until September 2013.
Section A: Wood Line 6
Modern woodyard: year 1972 with various improvements over the years. Production is 125 m/hr of logs.
Design capacity 62.5 cm³ wood per hour. Design speed is 0.5 to1.5 m / min. Camera system operated from central control station.
Log hopper for in feed of 8 m length logs. Two in feed lines 3.8 and 4.4 m wide. Maximum design load of conveyors is 63 tons.
Three sets of saws in conveyor system cutting logs to 1060mm lengths. Drive is 50 hp. Roll centring system before saws are 1500mm diameter.
De barking drum with rubber inner bark removing units: 5 m diameter and 30 m length.
Log conveyor with reject section with rejects going to a reject screen.
Kone/KMW chipper with single motor drive producing 350 m³/hr of chips. Chips transferred by chip screw into next stage.
Log conveyor system feeding debarked logs outside the building with option of feeding external log magazine or on-going to feed the groundwood plant.
KMW Chip screen
The system has its own self-contained water screening system and reject debris from in feed conveyors is continually cleaned from the base of the conveyors with waste going into the waste water system.
In operation until September 2013.
Section B: Groundwood
Groundwood plant for production of 200 t/day of groundwood
Year of manufacture: 1958 with various rebuilds. Production average 8.8 t/hr and rejects 3.4 t/hr.
Conveyor log feed to log magazines for logs.
Fork truck log transfer from magazines to log hoppers on grinders.
Six Voith grinders model 5 with log magazines. Motors are Schorch 3000 kW driving via gearbox to grinders.
Rotary screens feeding onto conveyor for pulp.
Screens for cleaning water from grinders. The screens have horizontal screen plates.
Five horizontal screens for coarse screening of the pulp model Celleco HRCC-4 .
First stage screening two Tampella model 36P, secondary stage two Tampella TL200 pressure screens.
Three stage screening by pressure screens:
Primary screen step 1: 45.A208 Basket with hole diameter 1.6 mm.
Primary screen step 1: 45.A210 Basket with hole diameter 1.6 mm.
Primary screen step 2: 45.A212 Basket with slot 0.15 mm.
Primary screen step 2: 45.A214 Basket with slot 0.15 mm.
Secondary screen: 45.A216 Basket with hole diameter 1.6 mm.
Secondary screen: 45.A218 Basket with hole diameter 1.6 mm.
Reject screen: 45.A274 Basket with slot 0.15 mm
Celleco Cleanpac LD cleaner system in three stages: first stage 80 cleaners, second stage 32 cleaners and
third stage 4 cleaners.
Two stainless DSM bow screens in one unit.
Celleco heat exchangers: model IH.
Hedemora disc filter for pulp thickening. Model VDF 45.A228 M 200734 and disc diameter 5m rebuilt by
GL&V. Inlet 0.5%, 30,000 litres/min, freeness 32 CSF, temperature 75 to 85 °C, design thickness in
accept pulp 9.52%. Filtrate 350 ppm.
Pressure screen: BCI 24P, stainless steel with gearbox drive for cleaning water.
Tanks for clear filtrate water and thickened pulp.
Pre - thickening screws feeding the Sudor model 150 screw press in stainless steel, motor and gearbox
drive.
Celleco screw press with Hagglund hydraulic drive.
CELLECO SCREW PRESS
Mixer for bleach then pulp fed into bleaching towers 170 m³ and 250 m³ capacity.
Tanks for rejects feeding screw thickeners which then feed Jylhavara SD 62 rejects refiner.
Stainless pulper for mixing pulp to the correct consistency.
Final stage screening.
Section C: Voith De inking system
Voith De inking system for 310 t/day with two stage medium consistency bleaching.
Was operating on 70% old newsprint and 30% old magazine papers.
Two Voith pulpers model VSG-50, capacity 72 to 170 t/day each, 280 kW drive, with bottom rotors,
gearbox drives, fed from B+G Fordertechnik balers on load cells.
VOITH PULPERS
Weighing on conveyors to control consistency.
Feed conveyor then diverter conveyor feeding individual conveyors to each pulper. Year of manufacture 1976. Operating at low consistency. Batch operation. Sectional stainless tubs with bottom mounted rotor
and gearbox drive.
Voith Contaminex stainless steel for pulper rejects, model CM21, year 1993, capacity 1500m3/hr. Motor 55 kW.
Voith screening drum in stainless: model F5, year 1993 and motor 5.5 kW.
Trumag scewpress: model Compax by Meri, year 1993 with motor 30 kW.
Three Voith Turbo separators : ATS 20 units, basalt tile lined, year 1977, motors 120 kW.
Three Voith HD cleaners with auto rejects.
Esher Wyess reject sorter: model RS2B, year 1987, for fibre removal from plastic rejects. Motor 55 kW.
Voith Spectro screen position 1: model GR33D, year 1993, stainless body with slotted basket 0.35mm and
power 160 Kw.
Voith Spectro screen position 2: model Gr23, year 1987, stainless body with slotted basket 0.35mm and power 90 kW.
Voith Spectro screen position 3: model Gr13W, year 1987, stainless body with slotted basket 0.35mm and power 37 Kw.
Five Voith primary flotation cells: stainless steel, model ECC5/41 , year 1993, capacity 17,000 litres/min.
PRIMARY FLOTATION CELLS
Two Voith secondary flotation cells: stainless steel, model ECC5/41, year 1993, capacity 17,000 litres/min.
Voith LD cleaner 1st stage: two sets of 18 cleaners, model KS200E, year 1976, flow 950 litres/min.
Voith LD cleaner 2nd stage: two sets of 4 cleaners, model KS200E, year 1976, flow 950 litres/min.
Voith LD cleaner 3rd stage: two sets of 1 cleaner, model KS200E, year 1976, flow 950 litres/min.
Voith screen position 1: four screens model GR23, year 1982, stainless body.
Voith screen position 2: two screens model Gr 1, year 1976, stainless body.
Voith Spectro screen position 3: model Gr13W, year 1987, stainless body.
Disc filter Hedemora manufacture, year 1978, stainless body with repulping screw, model VDF 5 m diameter and 19/20 discs.
HEDEMORA DISC FILTER
Micro floatation Flootec, year 1987, capacity 8000 litres/min, with pre flocculation tank, two floatation
cells and pre flocculation make up unit.
FLOOTEC MICRO FLOATATION
Andritz screw press in stainless steel model SPC1407 mm 11900, year 2005, capacity 387 BDT/D drive
400 kW.
Voith mixer for addition of bleach: model type GR30, year 1982 and motor 55 kW.
Two stainless Blekthorn MC bleaching towers.
Metso refiner LC position: model JCO-5, year 1999 with 2600 kW motor.
Voith primary flotation two with three cells in stainless steel: model ECC5/41, year 1993, capacity 17,000
litres/min.
Voith secondary flotation two with one cell in stainless steel: model ECC5/41, year 1993, capacity 17,000
litres/min
Disc filter Hedemora manufacture: year 1978, stainless body with repulping screw: model VDF 5 m
diameter and 19/20 discs.
Section D: Paper machine deckle 6650mm
Basement design paper machine producing lightweight printing papers with recent wet end and dryer
major rebuild in 1983. New wet end in 1997 by Valmet.
Machine is right hand drive from the flowbox with a sectional electric drive.
Grammage range 49 to 70 gsm. Average running grammages 52 to 55 gsm.
Average production at 54.3 gsm amd machine speed 1013 m/min is 433 t/day.
Machine efficiency approvimately 85%.
Average operational speed 1000 to 1050 m/min.
The machine house has two cranes and one will be retained with the building. DCS Valmet Dematic VME
stations rebuilt. Modern heat recovery system. Steam system pressures 10/6/2.5 bars.
Soleplate centres 7850mm and deckle after the rewinder 6650mm.
Design speeds:
Wire 1400m/min
Press sections 1000 m/min
Dryer section 1000 m/min
M Press sections 1000 m/min
Dryer section 1000 m/min
Machine drive designed maximum speed 1200m/min
Approach flow
Metso Deculator
LD cleaners in three stages.
Groundwood refiners: two Metso JCO-1 conical refiners.
Kraft pulp refiners: two Voith SDM-1 refiners with 30” diameter discs.
Back water fibre recovery by Nash vacuum assisted by Hedemora disc filter.
Four pressure screens prior to the headbox. Reject pressure screen in basement. Three Voith model
GR21 pressure screens year 1983 hole size 1.8 mm and one MODUScreen H3 with by Ahlstrom R with
0.25 mm slotted basket. Reject screen Tampella model 24P.
Machine has a variable speed fan pump.
Wire section
Flowbox Valmet HHSD 7080 mm slice width, dilution control , auto slice control actuators (total of 117).
Valmet Speedformer: model HSS.
Wire width: 7260mm
Soleplate centres: 7850mm
Dryness after the wire: 19%.
Press Section
Three press sections.
First and second press of Voith manufacture: double press rebuilt 1975.
Third press: Valmet SYMZS.
Dryness after press sections: 49 to 50%
Press maximum loadings: 55 kN/m first press, 100 kN/m second press and 130 kN/m third press.
Dryer section
The Voith manufactured dryer section in enclosed hood by Voith/Valmet in 1983, with front lifting doors.
Total of 60 dryers, all on A/F bearings with auto lub system.
Auto felt guiding and tensioning, steam and condensate at the rear of the dryers, sheathen rope tail feed,
operational pressure 2.5 bar. As indicated the dryer section had a complete rebuild in 1982 where it was
totally removed, new bearings fitted, painted, parts repaired and rebuilt, repainted etc.
Calender
The calender has only one roll remaining and is used as a lead roll for the Honeywell moisture spray
system. This section has an air transfer system from dryers through to the reel up.
Scanner: Metso IQ measuring gsm, profile, and ash.
Reel up
Voith horizontal reel up, rebuilt 1983, hydraulic operation, reel spool store above reel up, reel shell
accelerator, maximum reel diameter 2000mm. Reel transfer crane to the rewinder.
Vacuum pumps.
Nash 2001, 2001, 6002, 6002, 6002, 6002, 6002, 6002, 6002, 9001 and 9001.
Rewinder
Wartsilla rewinder: seven roll stations, centre reel design, reel shell unwind, design speed 2000 m/min,
auto knife setting, tension control, normal finished reel width 2600mm, maximum roll weight 3500 kgs.
Deckle after the rewinder 6650mm.
Salvage rewinder
Jagenberg Varistep rewinder: year 1986, 2600mm width, minimum slit 150mm, designed for 65 gsm.
Unwind shaftless with floor pick up: width 2600mm and diameter of 1250mm. Five slitters manual
setting, tail tape transfer, rewind diameter 1500mm to 400 mm, shaftless rewind with various rewind
diameter shafts, tension control, reel reject and lowering table, design speed 1500 m/min. Single motor
drive.
Supercalenders
Two Wartsilla supercalenders: model 12-6850, 12 rolls with soft and hard rolls, bottom Kuster roll and
top Nipco roll, steambox on second roll, and steam pipe on second roll. Maximum design pressure
280N/mm, speed 635 m/min. Each calender has horizontal lift for tail feeding. Spare roll rack with hard
and soft rolls.
Roll grinder/lathe
Mill has a roll store which has a horizontal lathe for cutting new surface on supercalender rolls. Also roll
rack which has individual drives to keep rolls turning before and after machining.
Section E: Turbines and Boilers
Turbines
1. Hallsta MTG5 maximum power 19.750 Kw. Stal manufacture and year 1971
Speed 3000 rpm.
Frequency 50 Hz.
Voltage 5250 V. Excitation voltage 220 V.
Steam temperature before control valve 530 °C.
Steam pressure before control valve: normal 100 bar and maximum 125 bar.
Extraction pressure: 10 bar and 4 bar. Back pressure 1.7 bar.
2. Hallsta Turbine High Pressure 17,500 Kva
Hallsta high pressure turbine, maximum power 17,500 Kw. Stal manufacture and year 1956.
Speed 3000 rpm.
Frequency 50 Hz.
Voltage 5250 V. Excitation voltage 220 V.
Steam temperature before control valve 530 °C.
Steam pressure before control valve normal 107 bar and maximum 127 bar.
Extraction pressure 45 bar and 6.2 bar. Back pressure 25 bar.
3. Hallsta Turbine Low Pressure 14,000 Kw.
Hallsta low pressure turbine, maximum power 14,000 Kw. Stal manufacture and year 1956
Speed 3000 rpm.
Frequency 50 Hz.
Voltage 5250 V. Excitation voltage 220 V.
Steam temperature before control valve: 350 °C, maximum 425 °C.
Steam pressure before control valve: normal 25 bar and maximum 40 bar.
Extraction pressure 6.2 bar. Back pressure 1.8 bar.
NB. Turbines 2 and 3 HP and LP were reconditioned in 1995.
Svenska Maskinverken Boilers
Number 1 Boiler for burning oil:
Year installed 1958, construction pressure 125 bar, operating pressure 80 bar, output of steam 566 t/day,
construction temperature 530 °C.
Number 2 Boiler for burning oil:
Year installed 1958, construction pressure 125 bar, operating pressure 80 bar, output of steam 566 t/day,
construction temperature 530 °C.
Number 3 Boiler for burning bark /oil:
Year installed 1970, construction pressure 125 bar, operating pressure 85 bar, output of steam 1044 t/day,
construction temperature 530 °C.
Number A Boiler for burning sludge / bark:
Year installed 1963 rebuilt 1985, construction pressure 25 bar, operating pressure 25 bar, output of steam
480 t/day, construction temperature 225 °C. This boiler is conveyor fed and has a fluidised sand bed.
Burning is assisted by oil addition.
Electrical scrubber filter unit ABB manufacture model TR1 and TR2: 5.5 MW.
Two redundant items.
Core Link core cutting system automatic set up control.
Reel handling system for rolls maximum 2600mm length and maximum diameter 1500mm.
THIS INFORMATION IS THE TITLE OF JOHN WILKIE PAPER
MILL SERVICES LTD AND SHOULD NOT BE COPIED OR
FORWARDED TO A THIRD PARTY WITHOUT CONSENT.
FOR YOUR GENERAL INFORMATION WE HAVE TO INTIMATE
THE FOLLOWING TO YOU:
This schedule has been prepared solely for the guidance of prospective
purchasers and does not constitute (and at no time shall be deemed to
constitute) an offer or contract or any part of an offer or contract.
Additionally, no warranty is given to the accuracy of any measurements,
specifications or other details whatsoever given within this schedule.
Whilst every reasonable effort has been made to verify any statement,
description, or comment made within this schedule, for the avoidance of
doubt it is emphasised that the purchaser must make their own enquiries
and satisfy themselves.
Ref. 51344
TISSUE MILL FOR SALES
TISSUE MILL FOR SALES
- Start up in 2004
- Width after rewinder 2.750 mm
- Max Speed mecanical 1.000 m/min
- Nominal speed 850 m/min
- Tissue papers from 17 – 30 gsm
- Capacity 20 – 38 Tpd
Stock preparation:
Conventional pulper at 6% capacity 15 m3 power installed 160 kW with metallic
belt conveyor, rejects on a trommel built on stainless steel
HDC Comer
Maule Separaplast GRII on stainles steel, rejects on a small trommel stainless
steel
3 stainless steel tanks ST with agitators
2 Toschi deflakers power installed each 55 kW
Double disc refiner Celli 20” with power installed 150 kW
Refiner PILAO Triconic with power installed 250 Kw
Stainless steel pipes
Pumps and regulation
Tissue paper machine:
Machine type fourdrinier
Fan pump Ahlstrom ZPP
Vertical screen on stainless steel ST with slotted basket 0,28 mm
Hydraulic Head box new in 2004 ST Italy, on stainless steel slice width 2.850
mm with profile control manual
Cantilever fourdrinier on stainless steel built new by SICMA composed by:
- Header roll diameter 500 mm
- Forming
- 7 foils
- 5 vacuumfoils
- Tensor and guides
Return roll 700 mm
Pick up section with suction
1st press type suction diameter 880 mm
2nd pres type blend drilled diameter 800 mm
Second hand yankee cylinder diameter 3.600 mm and useful width 2.900 mm,
press work 4 bar, with a set of 3 doctors
New FOMAT closed hood type DuoSystem on gas capacity 650ºC
Conventional pope reeler for a maximum diameters 2.000 mm with 5 – 7 spools
Completely CC drive:
- Header roll 176 kW
- Suction press 176 kW
- Yankee dryer 2 x 176 kW
- Pope reeler 30 h.p.
Vacuum system:
1 vacuum pump Azmec AL 100 with power 160 kW
1 vacuum pump Azmec AL 85 with power 130 kW
Lubrication unit
Boiler BONO on gas capacity arround 12.000 kg/h
Spare rolls for the paper machine
Clothes
Pumps and motors
Krofta SPC 20 on stainless steel
Rewinder:
- Built by Toschi
- 2 belt unwinders
- Speed maximum 1.000 m/min
- Maximum diameter rewind 1.500 mm
- Width after rewind 2.750 mm
- Shaftless rewind
Ref.51347
MG PAPERS MACHINE AND HEAVY TISSUE PAPERS
MG PAPERS MACHINE AND HEAVY TISSUE PAPERS
- Installed new in 2002 – 2003
- Width of the machine at pope reel 2.720 mm (net 2.700 mm)
- Stock preparation for 100 % recyclieng pulp
- Capacity 25 - 40 Tpd
Stock preparation:
Metallic belt conveyor, with 1.500 mm, with stainless steel helical pulper
capacity 15 – 18 m3 and secondary pulper type pear on stainless steel, with
power motor
2 High density cleaners
Hett separator type SP700, on stainless steel, with holes basket and rejects on
a stainless steel vibrating screen
Vertical screen Andritz type MODUSCREEN model F3, installed in 2000, slotted
basket and power 75 kW
Vertical screen Andritz type MODUSCREEN model F1, installed in 2000, slotted
basket and power 37 kW
Hot dispersion unit composed by:
- 3 + 1 screw type bakers on stainless steel
- High density screw press
- Kneader disperger
All the tanks on stainless steel also the pipes
Pumps Alhstrom
Regulation
Approach flow &Paper machine:
4 Vacuum pumps Siemens model 28E3320 2BY5-Z, power installed 90 kW
Vertical screen Lamort SPE8, stainless steel, installed in 2001
Refiner PILAO model RTC1000, installed in 2001, power 250 kW
2 vibrating screens on stainless steel
Machine
- Erected and start up in 2002 – 2003
- Speed maximum 800 m/mmin
- Basis weigth 20 – 90 gr/m2
- Completely close hood max temp 400 ºC
- Automathic pope reel
Stainless steel head box, with perforate rolls and control profile, slice width
2.800 mm
Stainless steel and cantilever fourdrinier
1st press section type suction press
Yankee dryer diameter 3.600 mm and press 6 bar, with 2 blend drilled press
section and close Hood high effiency
Automatic pope reeler for diameter 2.200 mm and spools
Sectional drive
Broke pulpers
Lubrication unit
Rewinder:
- Installed in 2003
- Speed maximum 1.500 m/min
- Diameter exit 1.500 mm
- Installed new in 2003
- 10 knifes installed
- Drive
Ref. 51348
