FOR LATEST OFFERS PLEASE VISIT OUR NEW WEBSITE www.bpmbllp.com

PAPER MACHINE TWIN WIRE WITH FORMER

Type of paper: Test-Liner, gypsum board and core board
Drive left from flowbox
Basis-Weight: 120-450 gsm
Paper width at reel: 2850 mm (wet-end prepared up to 3000 mm)
Actual Production: 45,000 Tons/year
The fibre treatment, pulper, cleaning, wet end, press section etc, etc is designed
for up to 70 000 tons.
Actual maximum working speed: (280) 200 m/min (wet-end prepared up to 450 m/min)
Power supply: 380 Volts/50 Hz
Two overhead cranes in machine house
THE MILL RAN UNTIL 31ST OF MARCH 2011.
MAIN UPGRADES
Bottom wire made in 1998
Top wire made in 2000
Top former made in 2005
Press part made in 1998
Stock preparation: to great extent from 1997, 2000
WET END:
Built complete NEW in 1998 (Bottom wire), in 2000 (Top wire) and in 2005 (Top former) by DGI fully in stainless steel.
BOTTOM WIRE:
Centre from breast roll to couch roll 22 m.
Machine centres 4.25 mtrs.
Hydraulic Head box complete in stainless steel (rebuilt in 2005 to dilution system with automatic  valves for profile control).
Pond width: 3100 mm for a maximum flow of 24,000 L/min
(1) Forming Board
(3) Hydrofoils
(4) Vacufoils for low vacuum with automatic vacuum valves and pre-separators
(2) Top former transfer box with automatic vacuum valves and pre-separators
(1) Dewatering box double chamber for medium vacuum with automatic vacuum valves pre-separators
(2) Top wire transfer boxes with automatic vacuum valves and pre-separators.
(3) Double chamber suction box for high vacuum with automatic vacuum valves and pre-separators.
(1) Breast roll of 640 mm with bearing housing in bronze. Includes cleaning doctor in stainless steel.
(1) Couch roll of 850 mm with two vacuum chambers. Shell and suction chamber in stainless steel.
(1) Helper roll of 640 mm with bearing housing in bronze. Includes cleaning doctor in stainless steel.
(7) Wire rolls of 280 mm with bearing housing in bronze designed for a wire tension of 7 Kg/cm. Includes cleaning doctors in stainless steel.
(2) High pressure shower for wire cleaning, 1 high pressure shower for couch roll shell cleaning, low pressure shower for wire rolls, cleaning, edge cutting shower & Tailcutter (automatic control by paper break).
(1) Automatic guide.
(2) Manual stretchers with gear-motor built in stainless steel.
(1) Automatic stretcher.
(1) Steam box.
(1) Couch pit.
Cantilever frame “C” type built complete in stainless steel.
Handrails and catwalks in stainless steel.
TOP FORMER:
(1) Inlet roll of 775 mm with cleaning doctor in stainless steel.
(1) Drive roll of 775 mm with cleaning doctor in stainless steel.
(2) Wire rolls of 425 mm with bearing housing in bronze.
Designed for a wire tension of 7 Kg/cm.
(1) Three chamber Inverted suction box (first chamber for low vacuum, and the other for medium vacuum) with curved plate. Built in stainless steel.
(1) High pressure shower for wire cleaning.
(1) Automatic guide.
(1) Automatic stretcher.
Cantilever frame “C” Type built complete in stainless steel.
Dryness Wire Part: 28%        Dryness Press Section: 50%
Speed on the papermachine is dependent on gsm. Maximum speed is 200 /min.
Normal working speed was from 180 - 200m/min down to 80-90 m/min.
Normal production was approximately 5 tons / hour regardless of thickness/gsm/raw material.

TOP WIRE:
Hydraulic Head box complete in stainless steel.
Pond width: 3100 mm for a maximu flow of 14,00 L/min
(1) Forming Board
(1) Hydrofoils
(2) Vacuufoils for low vacuum with automatic vacuum valves and pre-separators.
(1) Dewatering box double chamber for medium vacuum with automatic vacuum valves and pre-separators.
(1) Double chamber suction box for high vacuum with automatic vacuum valves with pre-separators.
(1) Breast roll of 640 mm with bearing housing in bronze. Includes cleaning doctor in stainless steel.
(1) Ply-bond roll of 800 mm built in stainless steel.
(1) Helper roll of 640 mm with bearing housing in bronze. Includes cleaning doctor in stainless steel.
(3) Wire rolls of 400 mm (2 units) & of 280 mm (1 unit) with bearing housing in bronze designed for a wire tension of 7 Kg/cm. Includes cleaning doctors in stainless steel.
(1) High pressure shower for wire cleaning & low pressure shower for wire rolls cleaning
PRESS SECTION:
Built complete NEW in 1998 by DGI.
Working Pressure: 70 kg/cm (1st Nip of K-Press)
100 kg/cm (2nd Nip of K-press)
150 kg/cm (1st Nip of Tem-Sec)
180 kg/cm (2nd Nip of Tem-Sec)
K-PRESS:
(1) Automatic guide.
(1) Automatic stretcher.
Cantilever frame “C” type built complete in stainless steel.
Handrails and catwalks in stainless steel.
Wire centres breast to couch roll 10 m
1st Nip press roll of 850 mm with rubber cover.
2nd Nip press roll of 850 mm with micro-rock cover cleaning doctor in stainless steel.
Suction press roll with 3 vacuum chamber. Shell and internals in stainless steel.
(11) Felt roll of 280 mm. Designed for 5 kg/cm felt tension.
(1) Paper roll of 280 mm.
(2) Uhle box with 2 slots. Built in stainless steel.
(2) Automatic felt guides.
(2) Automatic felt stretcher
(2) High Press Shower.
Cantilever frame in steel.
Handrails and catwalks in stainless steel.
TEM-SEC-PRESS (HOT PRESS):
(2) Press roll of 850 mm with rubber cover.
(1) Center roll of 2000 mm with hard-chromed coating cover.
(11) Felt roll of 280 mm. Designed for 5 kg/cm felt tension.
(1) Paper roll of 280 mm.
(2) Uhle box with 2 slots. Built in stainless steel.
(2) Automatic felt guides.
(2) Automatic felt stretcher
(2) High Press Shower.#
Cantilever frame in steel.
Handrails and catwalks in stainless steel.
Steam & condensate system for centre roll heating.
WET-END AND PRESS SECTION AUXILIARIES:
Hydraulic unit for press rolls loading.
Oil lubrication unit for press rolls bearing housing.
Multi-motor drive built by Control technics in 1998, 2000 & 2005.
Vacuum system consists of:
Low vacuum fan for bottom & top wire vacuo-foils
Medium vacuum fan for dewatering boxes.
Medium vacuum fan for Top Former.
Nash vacuum pump CL2001 for Couch roll low vacuum. Built in 1998
Nash vacuum pump CL3001 for K-press suction roll low vacuum. Built in 1998
Nash vacuum pump L8 for K-press 1st felt. Built in 1998
Nash vacuum pump CL2002 for Tem-sec 1st felt. Built in 1998
Nash vacuum pump CL2002 for Tem-Sec 2nd felt. Built in 2006
Nash vacuum pump CL3001 for K-press 2nd felt. Built in 1998
Nash vacuum pump CL4002 for K-press suction roll high vacuum. Built in 1998
Nash vacuum pump CL3002 for Couch roll high vacuum. Built in 2004
Nash vacuum pump CL3002 for Wire suction boxes. Built in 1998
Power cabinets with motor starters
Control panels by Siemens PLC.
DRYING SECTION:
17 Drying cylinders of 1250 mm.  Maximum working pressure: 4 Bar (recoded in 1995) complete with cleaning doctors and frame.
1 Yankee cylinder of dia. 3200 mm, frame but no touch roll
9 Drying cylinders of 1250 mm. Maximum working pressure: 4 Bar (recoded in 1995) complete with cleaning doctors and frame.
(90) Drying felt rolls of 200-220 mm.
(8) Automatic felt guides.
(6) Manual stretchers
(2) Automatic stretchers
Steam and condensate system Cascade Type built by Langbein.
Open Hood with extraction fans.
Heat recovery unit for building ventilation.
(2) Infrared frames for humidity profile control (966 Kw). Built by Compact In 2000.
Shaft line drive complete of gearboxes, pulleys and belts.
Reel up
Quality control system by LSC (Germany) for basis-weight and humidity profile both direction (cross machine & machine direction).
Pope reel for reels up to 2000 mm diameter. Built by Kværner Eureka in 1962, rebuilt in 2006
Jagenberg winder. Model VariDur 33-15, single motor drive
Double carrying drums dia. 400 x 3450 mm
Maximum speed: 600m/min mm (original speed: 800m/min)
Maximum finished reel diameter: 2100 mm
Min slitting 75 mm (about 36 knifes)
Shaft unwind with water cooled drum and pneumatic brakes.
Shaftless rewind and roll ejector
Roll floor mounted upender
Stretch wrapper wrapping in film
STOCK PREPARATION:
Capacity: 200 Tons/day
Conveyor: Built by STEKO, Year of manufacture: 1997
Pulper 30 m3: Built by DGI, Year of Manufacture: 1997.
Model: ECOPULPER EPG-30
Built in stainless steel, including ragger and reject handling. 
Installed Motor: 250 Kw/1500 rpm
(3) High Density Cleaner: Built by DGI, Year of Manufacture: 1997.
Model: HDC-3000 in stainless steel with automatic reject system.
(1) Turbo-separator: Built by Voith, Year of Manufacture: 1974
Model: ATS 20 With holes of 2.8 mm.
Installed Motor: 160 Kw/1500 rpm.
(1) Reject sorter: Built by Escher Wyss, Year of manufacture: 1983
 
Model: RS2 with holes of 2.4/2.8 mm.
Installed Motor: 55 Kw/1500 rpm
(1) KRIMA Dispersion system: Built by Cellwood Machinery, Year of manufacture: 1990, rebuilt in 2004. Consisting of:  
(3) Pre-thickeners model: SDPP 2040 with installed motor: 15 Kw
(1) Press model: RR 550 With installed motor: 45 Kw
(1) Plug screw model: T-PLSK3823 With installed motor: 22 Kw
(1) Heating screw model: 800x5500 With installed motor: 5.5 Kw
(1) Feeder model: T-INM 350 With installed motor: 4 Kw
(1) Dispersion system model: KD710 With installed motor: 410 kw
Spare de watering screw press SDPP 2040
 Design capacity 100 t/day
TOP LINE STOCK PREPARATION:
Capacity: 80 Tons/day
(1) Pulper 15 m3: Built by Black Clawson, Year of manufacturing: 1954
(1) Drum Thickener
(1) MODUScreen type C2R: Built by ANDRITZ, Year of manufacturing: 1999
With screen basket 2.5 mm holes, installed motor of:
(1) MODUScreen reject screen MODUScreen F0, screen basket 2.0 mm holes
(1) MODUScreen type F10: Built by Andritz, Year of manufacturing: 2000
With screen basket 0.25 mm slots
STOCK PREPARATION AUXILIARIES:
Agitators
Stock pumps by Andritz, Year of manufacturing: 1999-2003
Motor included. Some pumps are with frequency converter.
Complete Instrumentation including consistency transmitter, flowmeters, pressure transmitter,
Power cabinets with motor starter.
Regulation by Siemens PLC.
BOTTOM WIRE APPROACH FLOW:
4 Stage low density cleaner. Built by CYCLOTEC. Year of manufacture: 1998.
(1) Pressure screen. Built by DGI. Year of manufacture: 2000
Basket with holes of 2.5 mm with a capacity of 24,000 l/min.
Motor installed: 45 Kw/1500 rpm
(1) MODUScreen reject screen MODUScreen F0, screen basket 2.0 mm holes
Stock pump and fan pump built by Andritz.
TOP WIRE APPROACH FLOW:
(1) Pressure screen. Built by Andritz. Year of manufacture: 2003
Basket with holes of 1.8 mm with a capacity of … l/min.
Motor installed: 15 Kw/1500 rpm
Stock pump and fan pump built by Andritz
WATER TREATMENT
Disc filter by GL&V Celleco Center Disk CDP with 13 discs of 3360 mm in diameter.
Capacity: 600 m3/hr, made in 1992
Microfilter. Built by ALGAS in 2008. Model AMF 50 W for a capacity of 500 m3/hr.
AUXILIARIES:
Reject handling/transportation: Built by SpiracAS
Automation/operator interface: Built by LSC
Metering pumps 
6 Chemical tanks 
Starch unit
Several spare parts such as press roll, wire & felt rolls, suction press shell.
Helper roll
Electrical transformers (5kV/400V 1250kVA)
Gearboxes
Pumps
Electrical motors 0,75 Kw – 410 Kw
Bearing units to pumps, screens, pulper
1 complete pre-thickener
Press screw
Plug screw
Screen plates/rotors

Ref. 121214

COMPLETE 110" TRIM 2-PLY LINERBOARD FOURDRINIER PAPER MACHINE (1996)

PM Complete/Fourdrinier Machine
Complete 110" Trim 2-Ply Linerboard Fourdrinier Paper Machine (1996), 230 Mtpd, Basis  Weight 98-410 Gsm, 128" Wire Width Mecfab/Gl&V Fourdrinier, Top Table 180" Length, Bottom Table 610" Length, Triple Layer 128" Width Weavexx Htx V2 Forming Fabric, 24 Vacuum Foil Elements, Gl&V Filler Headbox Hydraulic (2005), 120" Pond Width, Dilution Control, Gl&V Liner Headbox Hydraulic (2007), 120" Pond Width, Bottom Wire Drive Gearbox Motor 200 Hp, 500 Volt Dc, 1750 Rpm, Cd504at Frame, Falk Gear Drive Type  208y2-Lb, 8.626:1 Ratio, Top Wire Drive Gearbox Motor 150 Hp, 500 Dc Volt, L409at Frame, Falk Gear Drive Type 2080y1-Ld, 4.053:1 Ratio, 2 Mecfab 53" Diameter Roll 2000  Pli Press Section, Gl&V 48 Can Dryer Section 150 Psi, Hood Exhaust And Heat Recovery System, Bailey Dcs System, 2-1 Kmw, Nipco 6 Zone Control Top Calender, Measurex Control System Scanner, Ellington Reel, Ellington 2 Drum Rewinder 5000  Fpm, Machine Speed 1550 Fpm, Mfg: Gl&V

Ref. 121218

VOIT OFFLINE COATING MACHINE

SM B with prewinder

Typ offline coating machine
Manufacturer Voit
Year of construction1989
Working width4,07 m
Trimed paper web width4,04 m
Sonstruction speed1.600 m/min
Operation speed1.100 - 1.400 m/min
Coat weight per side6 - 15 g/m²
Dry content93 - 95%
Coating application system blade coating Farbauftrag SDTA orLDTA
Coating assembly 2 coater (1 for each paper side), following IR-dryer, air float dryer and drying cylinder
Prewinder Voith

SM B auxiliary system information
Hood ventilation: 2 area ventilation, Wiessner
Tail threading: ropes, 11 mm
Oil/grease lubrication system: central lubrication for drying section, individual grease lubrication for guide roll
Hydraulic system: Voith
Control system of PM: SPS PCS7 / S5
QCS system of PM: Honeywell 2000 FX install 1988
Online colour-measurement: Gretagmacbeth ER50PRF install 2000
Electric drives of PM: Siemens PCS7 Masterdrive 500V DC
Web-brake camera-system: Procemex 7X

Ref. 1137