2 HIGH BLOOMING MILL
39” x 84 ½” BLOOMING & SLABBING MILL
Age: 1980
Products Previously Rolled:
Stainless and Carbon Steel
Ingots: Up to 21” square
Slabs: 5” thick x 43” wide
Rolled to thin slab 1.57” thick x 41 ½” wide
High Lift: 41 ½”
Equipment:
1200 Ton Mechanical Hot Shear:
Max. Opening: 16 ½” sq.
Hot Shear Conveyor:
20 rolls
14” diameter
Furnace Exit Table:
Length: 38 ½’
No. of Rolls: 16
16” dia. X 51” face
Approach Table No. 1:
Length: 64’
No. of Rolls: 26
16” dia. X 51” face
Approach Table No. 2:
Length: 41’
No. of Rolls: 17
14” dia. X 79” face
Front Rev. Table:
Length: 26’
No. of Rolls: 12
15 ¾” dia. X 98” face
Front Manipulator with (2) Side Guides and Lifting Fingers
2-Hi Mill Stand:
Mill Rolls: 39.3” dia. max. x 84.64” face
Bearings: Roller
Post Size: 34 ¼” x 21.65”
Screwdowns: Electromechanical, 230 V. DC
Two High Lift Spindles with Spindle Carrier
One 2-Hi Pinion Stand
Motor: Previously driven by single motor, 6800 HP, 60/120 RPM
Note: The slow speed single motor or over/under drive motors available upon request.
Back Reversing Table:
Length: 26’
No. of Rolls: 12
15 ¾” dia. x 98” face
Back Manipulator:
(2) Side Frames and Lifting Fingers
Run Out Table No. 1:
Length: 35’
No. of Rolls: 12
14” dia. x 84” face
Run Out Table No. 2:
Length: 73’
No. of Rolls: 24
14” dia. x 60” face
This equipment was used for a short period, dismantled, reconditioned, and has been in storage for several years. There is a large quantity of spares, including three sets of two each top and bottom roll chocks and bearings. All auxiliary motors are MD 800 Series. The weight of the equipment is approx. 1,500 tons.
Ref. 5125
ROSSI / EMIL WOLFF PEDRAZZOLI / DMS / MM, WIRE, COIL AND TUBE MACHINES/ MANUFACTURING LINES
01. EMIL WOLFF (DE) - spiral welded TUBE manufacturing line – 1968
diameters 159-1600 mm
- wall thickness 4-12 mm
- WELDING SPEED (=PRODUCTIVITY): 0,6-1,8 m/minute
- two LINCOLN welding units with 2x 1500 A
- coil weight: 3-18 t
- with ULTRASOUND control unit
- with tube end-lathe
- complete line
- under power
02. ROSSI (IT) - tube and closed profile manufacturing line - ROSSI - 1989
- pipe diameter 16,75-63,5
- wall thickness 1-4 mm
- speed 120 m/ min
- capacity 25000 t/ year
03. MECCANICA ADDA FER (IT) - tube and closed profile manufacturing line - 1997
- pipe diameter 12-35 mm
- wall thickness 0,8-3 mm
- coil weights 2 x 11t
- speed 120 m/ min
- capacity 10000 t/ year
04. CAMULT (IT) - coil slitting line - CAMULT 1500/4 - 1991
- 1-4 mm, coil width 1500 mm
- coil weight max 16 t
- capacity 60000 t/ year
05. PEDRAZZOLI (IT) - hydraulic cutting off machine - SCL 102 - 1999
- automatic
- upto 6 m length
- diameters between 12-102 mm
- saw blade diameter 315 mm
06. PEDRAZZOLI (IT) - hydraulic cutting off machine - SELF BROWN
- upto 6 m length
07. PEDRAZZOLI (IT) - pipe calibrating machine - STERN BROWN 65-2P/3P - 1996 diameter 65 mm
- length 230 mm
- speed 60 mm/ sec
WEIER (DE) - slitting line & coil tabling line - MOT GN 180L BREFT
- coil width 1500 mm
- coil width 15 t
- thickness 2 mm (slitting line)
- thickness 3 mm (coil tabling line)
- thickness upto 10 mm (sheet metail deviding)
POLISH (PL) - coil tabling line - overhaul in 2005
- parameters: thickness 2-6 mm, width 1700 mm
- coil holder for 20 t
- straightener
- shears
1. DMS tube production line - 1978/1998
can be sold with two cutting off machines only
2. MM tube production line - 1970/2001
can be sold with two cutting off machines only
3. DAWIS cutting off machine - 1978/2007
4. KIRSCHE deburring machine - 2001/2001
5. ADIGE cutting off machine - 1994/2007
6. PEDRAZZOLI cutting of machine - 1997/2001
7. RUTHNER strip slitting circle shears - 12/2001
8. Grit polishing unit - 2001 - 2001
9. Strip descaling/cleaning line - 2001
10. QUARTO (Sundwig) strip rolling machine - 1962/1987
11. 20 rolls strip rolling machine - 1962
12. DEMAG strip rolling machine - 1982/2001
- can be sold with the QUARTO (SUNDWIG) strip rolling machine (pos. no 10) only or with the 20 rolls strip rolling machine (pos. no 11)
13. RIPOSCHE electrical top hat furnace with protective atmosphere - 1980 piece
- 6 pieces available
14. SUNDWIG 500 strip slitting - 1962/1989
15. Binding line (SIEMI) - 1981
16. SUNDWIG 200 strip slitting - 1976
17. CW3 strip rolling machine - 1949
- can be sold with the QUARTO (SUNDWIG) strip rolling machine (pos. no 10) only
18. K3 type circle shears (strip) - 1974
- can be sold with the QUARTO (SUNDWIG) strip rolling machine (pos. no 10) only
19. SUNDWIG cutting off machine - 1964
- can be sold with the QUARTO (SUNDWIG) strip rolling machine (pos. no 10) only
20. Cutting of machine - 1970
- can be sold with the QUARTO (SUNDWIG) strip rolling machine (pos. no 10) only
21. QUARTO roll stand - 1987
- can be sold with the QUARTO (SUNDWIG) strip rolling machine (pos. no 10) only
52. MINO rolling mill - 1998
- photos and description
53. 40 wire galvanizing line - dia 1-3,5 mm - yom 1969
54. SIEMENS strip hardening and tempering line - 1962
55. RAU-BOING steel strip tempering line
56. EBNER (dinamo) furnace with varnishing
57. roller bottom furnace
Ref. 51214
EMI WOLFF SPIRAL WELDED TUBE MANUFACTURING LINE – 1968
Manufacturer : EMIL WOLFF (DE)
Year : 1963
Diameters 159-1600 mm
Wall Thickness 4-12 mm
WELDING SPEED (PRODUCTIVITY): 0,6-1,8 m/minute
Two LINCOLN welding units with 2x 1500 A
Coil weight: 3-18 t
With ULTRASOUND control unit
With tube end-lathe
Complete line
Under power
Ref. 51214
ROSSI TUBE AND CLOSED PROFILE MANUFACTURING LINE - ROSSI - 1989
Pipe diameter 16,75-63,5
Wall thickness 1-4 mm
Speed 120 m/ min
capacity 25000 T/ year
Ref. 51215
