Schuler KB2-630 Cold Extrusion Press
SCHULER KB2-630 COLD EXTRUSION PRESS 630T
KNUCKLE-JOINT COLD EXTRUSION PRESS 630t
Specifications:
Nominal press force: 630 Ton
Strokes per minute, variable: 25-50/min.
S.P.M. for inching, with reduced work energy: 10/min.
Slide stroke:315 mm
Slide adjustment: 20 mm
Main motor: 149 kW (200 HP), 1750/mn
Opening in upright width: 730 mm
Bed area (R-L X F-B): 1250 X 800 mm
Slide area (R-L X F-B): 1250 X 800 mm
Distance between oiltrays: 1260 mm
Shut height between bed, bolster plate and slide face: 960 mm
Bed ejector:
Pressure pins no.: 5
Stroke: 125 mm
Total force: 500 kN
Slide ejector:
Pressure pins no.: 5
Stroke: max. 69 mm
Total force: 125 kN
Ref. CGS101368
Smeral LKM 4000 Hot Forging Press
HOT FORGING PRESS SMERAL LKM 4000
Year of manufacture: 1966
Total width: 6280 mm;
Total depth: 4885 mm;
Total height: 8870 mm;
Height over the bed: 7315 mm;
Max pressure at the end of stroke: 4000 t.
Press stroke: 400 mm;
Number of stroke: 50 per minute
Max distance between ram and table: 1400 mm
Dimensions of ram: 1320 x 1320 mm;
Table dimensions: 1120 x 1600 mm
Table movement by height: 20 mm
Max pressure of upper ejector: 20 t;
Max stroke of upper ejector: 65 mm;
Max pressure of lower ejector: 40t;
Max stroke of lower ejector: 80 mm
Main motor power: 225 kwt
Main motor speed: 730 rpm
Total net weight: 280 t
Ref. CGS101369
KRAMATORSK 3150t, 13,8" Upsetter
Upsetter 3150t, 13,8" KRAMATORSK
KRAMATORSK
Technical specification:
Nominal Force, kN - 31500;
Movable die stroke, mm - 350;
Maximum upsetting ram stroke, mm - 700;
Upsetting ram work stroke, mm - 480;
Upsetting ram return stroke with closed dies, mm - 270;
Measurements of the dies, mm:
- Length-1020,
- Width-390,
- Height-1300;
Distance between upsetting ram and dies stroke forward, mm - 290;
Distance between bed and unmovable die, mm - 280;
Numbers of ram stroke per minute, Hub/Min - 23,5;
Lifting force of the pneumatic 3-notch table:
- using a cylinder with a Ø of 250 mm, t - 1,6,
- using a cylinder with a Ø of 360 mm, t - 4;
Max. Plunger stroke Ø 250 mm, mm - 800;
Max. Plunger stroke Ø 360 mm, mm - 540;
Main drive motor power, kW - 250;
Voltage, V - 380;
Complete power of the electric equipment, kW - 260;
Working pressure of the compressed air, kg/cm² - 5;
Max. Consumption of compressed air, m³/hour - 90;
Max. Consumption of water, m³/hour - 0,3;
Overall dimensions:
- Floor space, mm - 10305 x 7150,
- Height above floor level, mm - 4960;
Weight, t - 421,3
Ref. CGS101370
Duisburg Push Down, Water Hydraulic 7500 Ton Open Die Forging Press
DUISBURG HYDR. OPEN DIE FORGING PRESS 7500 TON
Brand : DUISBURG
Type : Push Down, water Hydraulic,
Pre-Stressed Frame,
4 Columns
Installed : 1955
Latest retrofits : 2008 / 2011
Technical dates :
This press comes with a multiplier that can increase the forging force up to 7500 ton
Nominal Force. 80 MN
Upsetting Force. 90 MN
Force at diff. Stages
4 colulmn Down Stroke 1 Cylinder 27 MN
2 Cylinder 54 MN
3 Cylinder 80 MN
Upsetting Force. 90 MN
Working Pressure At Force 60 MN 26,6 Mpa
Upsetting Force 75 MN 30 Mpa
Cylinder Diameter 1130 mm
Return Force - KN
Stroke 2500 mm
Admissible Eccentricity dia. - mm
Vertical Daylight 6150 mm
Pitch between Columns. in Working centreline 5000 mm
Pitch between Columns. Perpendicular 2500 mm
internal width inside columns with protection 4200 mm
Press height at ground level 13370 mm
full height 18060 mm
Longitudinal Table Useable area W x L 9180 x 3000 mm
Shifting force - KN
Shifting stroke AU side 4 m
Shifting stroke opposite 5 m
Die Shifting Device No. of dies in play No
Stroke No
Shifting Force No
Top Die Clamping Device Clamping Force
Mode of Hydraulic Drive -
Mode of Hydraulic Control -
Speeds 1 Cylinder (24 MN) - mm/s
2 Cylinder (36 MN) - mm/s
3 Cylinder (60 MN) 130 mm/s
Upset Speed - mm/s
Approach Speed 300 mm/s
Return Speed 500 mm/s
Table Shifting Speed 350 mm/s
Die Shifting Speed No
Cycling Frequency Idling 24 MN 25 Stroke/min
Cycling Frequency Idling 36 MN 25 Stroke/min
Cycling Frequency Idling max force 25 Stroke/min
Ejector no
Ref. CGS101385
