ANDRITZ 160 T4 - 1989
ANDRITZ 160 T4 - 1989
Wire rolling mill
160 T4
1989
conventional
PRECISION - FLATWIRE - TANDEM ROLLING MILL
technical details
Construction: ANDRITZ
Typ: 160 T4
Year: 1989
Working range:
for example: Entry: round- Ø 1,6 - 4,5 mm steel
Exit: Ø 2 - 9 mm x 0,25 -0,40 mm
Number Working Rolls: 4 Pieces
Rolling speed: max. 600 m/min.
The Line consists of:
- Decoiler weight: max. 1300 kg, drive motor 10 kW
- vertical und horizontal straightening machine
- Duo Working Roll No. 1 Rolls: Ø 160 mm, drive motor 58 kW
- Duo Working Roll No. 2 Rolls: Ø 160 mm, drive motor 58 kW
- Turk-head - Rolling Mill
- Duo Working Roll Nr. 3 Rolls: Ø 130 mm, drive motor 42 kW
- Turk-head - Rolling Mill
- Duo Working Roll Nr. 4 Rolls: Ø 130 mm, drive motor 42 kW
- Spooler, loading capacity max. 800 kg, drive motor 13 kW
Total weight: approx. 36 to.
Description:
inlet at round wire 1,6,,,,,,4,5 mm
finish-diameter - max. 2 - 9 x 0.25 - 0,4 mm
Number of stands 4 pcs
material Stahl, NE Steel, Non
Ref. CGS81347
Farrel/Presezzi/Turla 2250 Mton Extrusion Line
2250 Mton Extrusion Line, Farrel/Presezzi/Turla, (complete renewed in 1999 - 2004)
Type oil-hydraulic direct
Billet diameter 8 inch
Billet length 800 mm
Main pumps 4 x Oilgear
The line consists off:
- gasheated log heater, TURLA, 7000 mm long
- double Puller, TURLA
- belt-type handling table, 51 m long
- 40 ton Stretcher
- Automatic profile stacker
the line is out of operation
Ref. CGS9132
Haginger 2350 Mton Extrusion Line
2350 Mton Extrusion Line, Haginger, new in 1991 (modernized in 1999)
Type oil-hydraulic direct
Billet diameter 178 & 228 mm
Billet length 1000 mm
Drive 3 x 200 kW Oilgear
The line consist off:
- gasheated log heater, ELHAUS, 7000 mm long
- run-out table with single Puller
- belt type handling system,42 m long
- 90 ton Stretcher
- finishing saw
the line is still in operation until November 2013
Ref. CGS9133
Zam, Demag-Technika Melting And Casting Lines
5 Second-hand melting and casting lines
Mfc.: ZAM, DEMAG-TECHNIKA,
Built: qty. 3 in 1989, 1994 & 2001
Strip width: 300 – 450 mm
Thickness: 13 – 18 mm
Prices Built 1989:
Built 1994:
Built 2001:
Melting and casting lines – 5 units
Melting and casting line no 1, no 2, no 3 – year 1989
Including:
Channel type induction melting furnace PIK 1500 made by ZAM
- Total capacity 3600 kg
- Charge capacity 1500 kg
- Active power 340- 410 kW
- Frequency 50 Hz
- Inductor voltage 500 V
- Induktor system – Scottea
– Melting speed: 1200 kg/h - 1850 kg/h
Channel type induction casting furnace by Demag
– Technica
Total capacity 2800 kg
- Active power 150 kW
Frequency 50 Hz
- Voltage rate 500 V
Capacity 1500 kg.
Flat mould consisted with closed frame, copper cooler and graphite mould with the following parameters
thickness 13 to 18 mm
- width 300 to 450 mm
length 250 mm
4. Drawing machine – by Demag Technika used for drawing a strip out from a mould
5. Milling machine FR4 with a spray cooling by Demag - Technica used for both side strip milling.
Max. Milling thickness 1.5 mm on side
Max. width 450 mm
- Power of hydraulic unit drive 2.2 kW
Feed speed 64-640 mm/min.
- Transport rollers dia. 138 mm
Mill spindle dia 140 mm
- Speed of spindle milling 140 mm/min.
6. Flying shear – by Demag Technica, used for cutting of the strip in movement, sizes:
max. strip size 20 x 450 mm
- max. cutting power 1750 kN
Working preasure 140 bar
- Power of hydraulic unit drive 5.5 kW
7. Coiling machine – by Demag
– Technica used for coiling of casted strips
max. strips width 450 mm
- max. thickness of strips 18 mm,
Inside dia. 600 mm
- Outside dia. 1800 mm
Coiling speed 1.6 m/min.
- Power of coiling drive 1.5 kW
Power of coil drive 0.55 kW
Melting and casting line no. 4 – year 1994
Equipment composition same as line 1, 2, 3
Melting and casting line no. 5 – year 2001
Including:
1. Channel type induction melting furnace PIK 1500 by ZAM
Total capacity 3600 kg
- Charge capacity 1500 kg.
Active power 340- 410 kW
- Frequency 50 Hz
2. Channel type induction casting furnace by Demag – Technica
Total capacity 2400 kg
- Active power 150 kW
Frequency 50 Hz
3. Flat mould consisted with closed frame, copper cooler and graphite mould with the following parameters
thickness 13 to 18 mm
- width 300 to 450 mm
length 250 mm
4. Drawing machine – by Demag Technika used for drawing a strip out from a mould
5. Milling machine FR4 with a spray cooling by Demag - Technica used for both side strip milling.
Max. milling thickness 1.5 mm on side
max. width 450 mm
6. Flying shear – by Demag Technica, used for cutting of the strip in movement, sizes:
max. strip size 20 x 450 mm
7. Coiling machine – by Demag – Technica used for coiling of casted strips
max. strips width 450 mm
- max. thickness of strips 18 mm
Inside dia. 600 mm
- Outside dia. 1800 mm
Ref. CGS9136
