MÜLLER WEINGARTEN M 2000 HYDRO FORMING PRESS
HYDROFORMING Press MÜLLER WEINGARTEN
Type M 2000 (YOM 1999 / installed 2002)
This press was ONLY used in the university for research
for the automotive industry.
Capacity 2000 t
Table surface 2000 x 2000 mm
Ram surface 2000 x 2000 mm
Air pressure 250 bar
Working time less than 500 strokes
Attention the hydraulic aggregate has to be bought new as
the university has one central.
Ref. 3131
DNEPROPRESS PA1341 OPEN DIE FORGING HYDRAULIC PRESS
Complex Open die forging hydraulic press PA1341,
1. Press PA1341, new in 1975, made in Dnepropress, Ukraine
2. Manipulator 5ton, new in 1962, made in Russia, Elektrosteel
3. Pump-accumulator station.
3.1. Pump GГ305A – 3pcs.
New in 1975
Made in Russia, Tyagstankohydropress
3.2. Air balloon - 2 pcs
New in 1974
3.3. Hydraulic ballonn– 1pcs.
New in 1975
4. Motor sinhronous SDN 500kBt – 4pcs
5. Filling press V=2,5м³ - 1pcs
Specification :
1. Force: I station 260
II station 800
III station 1250
2. allowable eccentricity, 125mm
3. Maximum course traverse, 1250mm
4. Distance bеtween table and traverse in the top position, 2650mm
5.The distance between the clear across lower part of the rack forging axis, 1900 mm
6. The distance between the light along a lower part of the rack forging axis, 900 mm
7. Dimensions sliding table, width 1250 mm, length 3150 mm
8. Progress out tables regarding the press axis, one way 1400 mm & other side 1400 mm
9. Effort to move the sliding table, 30 t
10.Speed move the sliding table50-300 mm / sec
11.force ejector, 63T
12.Hod ejector over the table, 400mm
13.Number position change mechanism of the lower firing pin 3
14.Speed walking beam, at idle 300mm / s,
during the return course of 300 mm / s:
at working stroke (power up to 75% of nominal) 150
15.Number walking beam moves, however, strokes / min:
- working under a force of up to 75% of the nominal when the value of the stroke, mm
160 16
80 38
16.Precision automatic forging ± 1,5mm
17.Control: hand;
semiautomatic (manual with automatic stop walking beam on the mood
lower amount; automatic.
18.Drive: pump-accumulator station
19.Workinf liquid water emulsion
20Force working fluid 320 kgf/cm2
21.Aktive battery capacity, l 500
22.Capacity pump station, l / min 500
23.force air in the vehicle, 6.8 kgf/cm2
23. Envelope press, mm: length 16 940
width 11540
height of 11,410
24.Gabarit press with ejector mechanism and the shift of the lower
strikers, mm:
length width 16 940 x 13 740
height 11,410
25.Hight press from the floor, mm 7270
26.Weight, kg:
press 256000
press with ejector 258,000
press with a lower shift mechanism strikers 268,300
press with ejector mechanism and change
lower strikers 271,000
press without electro-hydraulic, strikers,
overlaps 135,000
Forging manipulator, Q = 5t
1. Payload 5tn
2. Maximum load moment at the grip 12 mM
3. Workpiece diameter: maximum 720 mm
minimum 100 mm
4. Stroke 200 mm jaws
5. Track width of 2700 mm
6. Trolley base 3700 mm
7. The distance from the horizontal to the trunk rail head:
maximum 1450 mm
minimum 950 mm
8. Ticks away from the rail head:
maximum 1775 mm
minimum 385mm
9. The value of the parallel movement of the trunk in a vertical plane 500 mm
10. Swing angle to the horizontal axis of the trunk: Up 7 º 30 '11 º down
11. The speed of rotation around the axis of the trunk 14.6 rev / min
12. Swing speed trunk ticks 3.5 m / min
13. Swing speed trunk levers 2.08 m / min
14. Rate of rotation of the upper bogie frame 3.78 / min
15. Trolley speeds of 40 m / min
16. Total motor power 98 kW
17. Manipulator control: kontroller
18. Maximum fluid pressure 80kg/sm ²
19. Weight 49.5 tonnes
Ref. 3135
NKMZ K8548 6 300 METRIC TONS HOT FORGING PRESS
HOT FORGING PRESS 6 300 METRIC TONS MODEL K8548 (MAKE NKMZ)
Technical description of the press
Nominal force 6,300 metric tons
Number of continous strokes per minute 40
Ram stroke 460 mm
Distance between ram and table (table is in upper position) 1,150 mm
Table adjustment 15 mm
Distance between press columns 1,950 mm
Ram dimensions
front to back 1,680 mm
left to right 1,680 mm
Table dimensions
front to back 1,950 mm
left to right 1,920 mm
Mechanical upper ejector
maximum stroke 100 mm
number of positions 1
steps of stroke adjustment 25-30-75 mm
force 30 tons
Pneumatic lower ejector
maximum stroke 300 mm
stepless stroke adjustment 15-300 mm
number of positions 3
force 65 tons
Side windows dimensions
width 1,100 mm
height 1,280 mm
Main montor 400/590 kWt/rpm
Press layout dimensions 6 300 x 8 965 mm
Total height 11,125 mm
Height above floor level 9,150 mm
Total weight 626,100 kg
Ref. 3136
WAGNER KFRWT 400 ROLLING MILL
Rolling Mill KFRWT 400
Made by: WAGNER Germany, mechanical action of milling disc, with four workstations, Max. outer diameter of piece 400 mm. The rolling mill is manufactured by WAGNER Germany
WAGNER Germany, mechanical action of milling disc, with four workstations, Max. outer diameter of piece 350 mm. The rolling mill is manufactured by WAGNER Germany.
Ref. 31310
