RYAZAN 2426, 4 ROLL PLATE BENING MACHINE
RYAZAN 2426, 4 ROLL PLATE BENING MACHINE
roll plate bening machine RYAZAN 2426
new 1976
very fine working conditions
Sheet 40*3150 mm
Dia upper roll 600 mm
Weight of machine 90 ton
Ref. 111279
HAEUSLER 4-ROLLER SHEET METAL PLATE BENDING MACHINE
1 Unit: Used 4-Roller Sheet metal Plate Bending Machine
Make: HAEUSLER
Made in Switzeland
Technical Data:
Max. Sheet Plate width: 3500 mm
Bending at a yield point of metrial of 240 N/mm² 55 mm
Prebending at a yield point of material 2460 N/mm² 65 mm
Good condition ex WAREHOUSE Available now
Ref. 111281
DNEPROPRESS P204 HYDRAULIC 4 POST STAMPING PRESS
Hydraulic 4 post stamping press, capacity 5000 tons, mod. P204
A stamping press working in an automatic mode of operation and single strokes mode.
Manufacturer - "Dnepropress", 1972 YOM
Technical specification:
Capacity - 5000 tons
Intermediary effort stages on single stroke operation with/without hold-down – 4000/2650 tons
Effort of hold-down cylinders - 1000 tons
Effort of lifting cylinders - 100 tons
Effort of table lifting cylinders - 100 tons
Ejector capacity - 250 tons
Daylight between columns:
- from the loading side - 4000 mm
- from lifting cylinder side - 1600 mm
Open height of the press - 1100 mm
Moving cross beam stroke - 600 mm
Permissible eccentricity of load at effort 5000 t - 150 mm
Speed of idle stroke of cross beam – 120 mm/sec
Speed of working stroke of cross beam:
- at 5000 t capacity - 15.5 mm/sec
- at 4000 t capacity - 18 mm/sec
- at 2650 t capacity - 28 mm/sec
The speed of reverse stroke of cross beam - 105 mm/sec
The speed of hydraulic cushion table raise - 65 mm/sec
Strokes per minute at 4000 t capacity – 1
Rated power of electric engine - 775.4 kw
Working fluid – oil
Working fluid pressure – 200 kg/sq.cm
Dimensions:
- height over the floor level - 7355 mm
- height under floor - 5825 mm
- width - 7780 mm
The size of loading table – 3650 x 2000
Press weight - 480 tons
Ref. 11338
DNEPROPRESS P204 HYDRAULIC 4 POST STAMPING PRESS, CAPACITY 5000 TONS
Hydraulic 4 post stamping press, capacity 5000 tons, mod. P204
A stamping press working in an automatic mode of operation and single strokes mode.
Manufacturer - "Dnepropress", 1972 YOM
Technical specification:
Capacity - 5000 tons
Intermediary effort stages on single stroke operation with/without hold-down – 4000/2650 tons
Effort of hold-down cylinders - 1000 tons
Effort of lifting cylinders - 100 tons
Effort of table lifting cylinders - 100 tons
Ejector capacity - 250 tons
Daylight between columns:
- from the loading side - 4000 mm
- from lifting cylinder side - 1600 mm
Open height of the press - 1100 mm
Moving cross beam stroke - 600 mm
Permissible eccentricity of load at effort 5000 t - 150 mm
Speed of idle stroke of cross beam – 120 mm/sec
Speed of working stroke of cross beam:
- at 5000 t capacity - 15.5 mm/sec
- at 4000 t capacity - 18 mm/sec
- at 2650 t capacity - 28 mm/sec
The speed of reverse stroke of cross beam - 105 mm/sec
The speed of hydraulic cushion table raise - 65 mm/sec
Strokes per minute at 4000 t capacity – 1
Rated power of electric engine - 775.4 kw
Working fluid – oil
Working fluid pressure – 200 kg/sq.cm
Dimensions:
- height over the floor level - 7355 mm
- height under floor - 5825 mm
- width - 7780 mm
The size of loading table – 3650 x 2000
Press weight - 480 tons
Ref. 11350
